M550-EC NG Natural Gas Tankless Water Heater
- Endless hot water, on-demand
- Designed specifically for the marine environment
- Weight 30.5
- Dimensions 13.5” Wide x 13.5” deep x 14.5” High. The power vent is an additional 2 inches.
- No pilot light for safety and insurable
- Straightforward installation.
- Reliable, proven VariFlame technology control system
- Complies to ABYC recommendations as an attended appliance when installed per instructions
Price: $1,555
Submit your review | |
Hot Water in Any Season
The PrecisionTemp M550-EC NG tankless, marine water heater utilizes our patented VariFlame Control technology to deliver an endless flow of hot water for the ultimate marine shower.
The heater operates only when the hot water outlet is turned on. The VariFlame control system then keeps the water temperature constant regardless of the flow rate or incoming water temperature.
The Proof is in the POWERWith 55,000 BTUs—the highest hot water output in the industry—and built-in freeze protection, the M550-EC NGdelivers on-demand, continuous hot water—all without using engine or shore power.
Quiet and EfficientFor the same amount of natural gas, the M550-EC NG produces more hot water than a traditional water heater.
Many people find that they use up to 50% less natural gas, with lower operating costs and fewer fill-ups. It’s lightweight, compact, efficient and installs almost anywhere.
| Type: | Gas instantaneous, power vented. Full gas modulation temperature control. |
| Dimensions: | 13.5″ Wide x 13.5″ Deep x 14.5″ High, including power vent. |
| Weight: | 30.5 pounds full. |
| Hook-ups: | Electric: 18-2 x 2′ lead. Gas: Brass 3/8″ flare inside case, rear accessible. Water: 1/2″ OD copper tubing. Brass compression to 1/2″ NPT elbow can be installed or as specified. |
| Capacity: | 55,000 BTU input – 44,000 BTU output at maximum burn at 3.5; WCI manifold pressure. (88°F temperature rise per gallon per minute continuous flow at high burn). |
| Fuel Consumption: | 2.55 lbs per hour at maximum input. (At 2 GPM of water, 20 lbs of natural gas will produce over 940 gallons of hot water). |
| Mounting: | Floor mounted flanges (included) |
| Clearances: | Zero clearance top (blower), bottom and sides. 2″ in back for hook-ups. Enough space in front to remove cover for service. |
| Venting: | 2” power vent with proofing switch. (2” stainless flex duct recommended to the outside, and can run up to 15′). |
Construction: | Modular: Three assemblies; gas, electronics and water. Burner: High primary air, 12 element, atmospheric type. Aluminized steel body with stainless flame strips. Heat exchanger: Copper fin tube type with wrap for cooling. Electronics: Plug in, potted, works-in-a-drawer. Burner and flue assembly are stainless steel. |
| Fuel: | Natural Gas @ 3.5 WCI |
| Power: | Burner: 12 element high primary air, atmospheric type with stainless steel construction. Orifices: Brass # 58 x 12.Gas Valve: Redundant solenoid with integral regulator. |
| Water Temperature: | Adjustable |
| Mounting: | Mounting flanges included. Must be mounted in accordance with any applicable Coast Guard and ABYC recommendations. As an attended applicance. |
| Safety Features: | The M550-EC NG is pilotless. There is no flame unless water flow is sensed.Flame rectification: Gas valve shuts off in .8 of a second if there is a flame outage. Redundant gas solenoid. Electronic high temperature shut-off (2). ECO high temperature shut off @ 165°F with manual reset.Pressure relief valve at 100 PSI. Power vent must proof fluing before gas valve opens. |
| Disclaimer: | Due to continuous product improvement, PrecisionTemp reserves the right to change specifications at any time. |
Related Video:
Not Avilable